top of page

Locomotive Audio Weight Tank WT-COMP – Vari-Mu Tube Compressor


The Locomotive Audio Weight Tank WT-COMP is a single-channel analogue tube compressor that combines soft-knee vari-mu compression with deliberate harmonic colour.


Two vacuum tubes and three all-steel transformers form a signal path designed to make an audible contribution. Variable attack and release controls shape the compression response, while ROUND and DRIVE modes offer different degrees of tonal intensity.


Use it when a recording needs more than level control: the WT-COMP is intended to influence dynamics, texture and the way a source occupies the mix.


Vari-mu compression with a soft knee


The WT-COMP uses a variable-mu tube gain-reduction circuit rather than a VCA, FET or optical gain-control element.


Its soft-knee characteristic brings compression in progressively around the operating threshold. This provides a different response from an abrupt hard-knee transition, while the input level and timing settings determine how firmly the signal is controlled.


The result is not restricted to subtle gain reduction. The Weight Tank is designed to move from gentler levelling towards more obvious compression and harmonic character.


Two tubes and three transformers


The audio path uses one 6BC8 and one 12AU7 tube, together with input, interstage and output transformers.


These stages are central to the product’s character. The WT-COMP is not presented as a transparent utility compressor that leaves every aspect of the source unchanged.


Locomotive Audio describes its sound in terms of weight, harmonics and colour. In practice, the useful amount depends on the recording, the level feeding the circuit and the role of the source in the arrangement.


Input and output controls


The INPUT control is the main way to drive the compressor into gain reduction. Raising it changes how strongly the source interacts with the circuit.


OUTPUT adjusts the level sent to the next device, allowing you to balance the processed signal with your converter or following processor.


These controls work together. After changing the input setting, readjust the output and compare at a similar listening level so that a louder signal is not automatically mistaken for a better one.


Variable attack and release


Separate ATTACK and RELEASE controls let you adapt the compression envelope to the performance.

The published timing ranges are 12–50 ms for attack and 200 ms–2 seconds for release. These settings provide scope for adjusting the balance between initial articulation and sustained level control.


A slower attack can retain more of the beginning of a note, while release should be evaluated against the rhythm and phrasing of the material. The right setting is the one that supports the performance rather than making the gain-reduction meter behave in a particular way.


ROUND and DRIVE


ROUND is the manufacturer’s smoother, sweeter voicing. DRIVE changes the behaviour of the output-tube stage to produce a more harmonically pronounced, driven result.


This makes the mode switch a tonal choice, not simply an alternative compressor timing setting.

Compare both modes on the same passage and rebalance the output where necessary. DRIVE can be useful when a source needs a more assertive texture, while ROUND provides a less overt starting point.


Gain-reduction metering and true bypass


A large illuminated analogue meter displays gain reduction, giving a direct view of the compressor’s action.


True bypass allows comparison with the unprocessed signal path. Use it alongside level-matched listening to judge whether the combined compression and colour are helping the recording.

The meter shows gain reduction; it should not be treated as a substitute for monitoring the input headroom of your audio interface or the peak level inside the DAW.


For tracking and mixing


The WT-COMP can be used in a line-level recording chain after a microphone preamplifier or as an external processor during mixing.


Vocals, bass, guitars, keyboards and drum sources are useful starting points for exploring its combination of levelling and harmonic colour.


It is not a microphone preamplifier or a direct instrument input. Connect microphones and instruments through suitable upstream equipment, and route the compressor through the appropriate line-level inputs and outputs of your studio system.


One channel per unit, with stereo-link capability


Each WT-COMP processes one audio channel. A stereo setup requires two units and the appropriate link connection.


Linking two compressors does not turn one unit into a two-channel processor. Both audio channels still require their own signal paths, and the input, output and timing settings need to be configured carefully.


Confirm the correct link cable and setup procedure for the supplied revision before installation.


A dedicated 2U rack processor


The Weight Tank WT-COMP occupies two rack units in a standard 19-inch rack and uses an internal mains power supply.


Confirm the supplied mains configuration, fuse requirements and installation clearance before connecting the unit. Allow suitable ventilation around tube equipment and follow the manufacturer’s operating instructions.


Is the Weight Tank WT-COMP right for your studio?


Choose the WT-COMP if you want analogue dynamics processing that also contributes a recognisable tonal character.


Its appeal lies in the combination of soft-knee tube compression, transformer colour, straightforward controls and two distinct voicings—not in automatic recall or an extensive menu of processing options.

Contact Falkenstein ProAudio to confirm current availability, the supplied hardware revision, mains configuration and any accessories required for stereo operation.


Specification

Locomotive Audio Weight Tank WT-COMP

Processor type

Analogue vari-mu tube compressor

Audio channels

One, mono

Compression characteristic

Soft knee

Tubes

1 × 6BC8, 1 × 12AU7

Transformers

Three all-steel transformers

Transformer positions

Input, interstage and output

Input control

Variable

Output control

Variable

Attack

12–50 ms

Release

200 ms–2 seconds

Tonal modes

ROUND / DRIVE

Metering

Illuminated analogue gain-reduction meter

Bypass

True bypass

Stereo linking

Yes; requires two units

Audio connections

XLR input and XLR output

Link connection

Rear-panel jack; required cable type to be confirmed

Rack format

19-inch, 2U

Power

Internal mains supply with IEC inlet

What is the Locomotive Audio Weight Tank WT-COMP?


The WT-COMP is a mono vari-mu tube compressor with three transformers and selectable ROUND and DRIVE voicings.


What is the difference between ROUND and DRIVE?


ROUND provides the smoother voicing. DRIVE produces a more pronounced harmonic character.


How is compression adjusted?


INPUT controls how strongly the signal drives the compressor. OUTPUT sets the level sent to the next device. Attack and release are independently adjustable.


Can the WT-COMP process stereo?


Stereo operation requires two units and the appropriate link connection. Each unit processes one audio channel.


Does it have true bypass?


Yes. The WT-COMP provides true bypass and an illuminated analogue gain-reduction meter.


Can I connect a microphone or guitar directly?


No. The WT-COMP requires a suitable line-level signal from a microphone preamp, instrument preamp or audio interface.

Locomotive Audio Weight Tank WT-COMP – Vari-Mu Tube Compressor

1.359,00 € Standardpreis
1.159,00 €Sale-Preis
inkl. MwSt.
Anzahl
Noch keine Bewertungen vorhandenJetzt die erste Bewertung abgeben.

© 2026 by Falkenstein ProAudio

bottom of page